I get commissions for purchases made through links in this post.
Replacing a water heater might sound daunting, but with the right tools and a bit of know-how, it’s a manageable task that can save you money on professional installation. Whether your water heater is old, inefficient, or broken, here’s a detailed, step-by-step guide to help you replace it with ease.
1. Turn Off the Power and Water Supply
Before you do anything, ensure the water heater is completely disconnected from its power source.
- Electric Water Heater: Turn off the power by switching off the circuit breaker that powers the water heater.
- Gas Water Heater: Turn the gas valve to the “off” position. Also, shut off the water supply by closing the main water valve.
- Water Supply: Turn off the cold-water supply valve to the water heater to prevent water from flowing into the tank while you work.
2. Drain the Tank
You’ll need to drain the tank to avoid any spills while removing the old water heater.
- Attach a Hose: Connect a garden hose to the drain valve at the bottom of the tank.
- Open the Valve: Open the valve to start draining the water. Allow the tank to drain completely (this may take some time depending on the size of the tank).
- Open a Hot Water Tap: To speed up the draining process, open a hot water tap in the house to allow air to enter the system and help the water flow out more easily.
3. Disconnect the Water Lines
Once the tank is drained, disconnect the cold and hot water lines.
- Use a Wrench: Use an adjustable wrench to loosen the nuts that connect the water lines to the tank. Be prepared for some residual water to leak out when you remove the hoses.
- Remove Any Flex Hoses: If the water lines are attached with flexible hoses, simply unscrew them by hand.
4. Disconnect the Power Supply
Now that the water is drained, disconnect the power supply to the water heater.
- For Electric Models: Unscrew the access panel on the top of the water heater. Use a voltage tester to ensure there’s no power in the wires, then disconnect the wiring by removing the screws on the wire connections.
- For Gas Models: If your water heater runs on gas, unscrew the gas line from the heater using a pipe wrench. Be sure to check the connection for any gas leaks once it’s disconnected.
5. Remove the Old Water Heater
With everything disconnected, it’s time to remove the old unit.
- Lift the Tank: If the water heater is small enough, you may be able to lift it out by yourself. For larger models, you’ll likely need help.
- Use a Dolly or Cart: For larger models, use a dolly or cart to safely move the old water heater out of the area.
6. Install the New Water Heater
Now that the old water heater is removed, it’s time to install the new one.
- Position the New Heater: Place the new water heater in the same spot as the old one. Ensure it’s level and properly aligned with the existing plumbing.
- Connect the Water Lines: Reattach the cold and hot water lines to the appropriate inlets on the new tank. Tighten the connections with an adjustable wrench to ensure a secure fit.
- Reconnect the Power or Gas Supply :
- For Electric: Connect the electrical wires to the appropriate terminals on the new water heater, making sure the connections are tight and secure. Replace the access panel and turn on the power at the circuit breaker.
- For Gas: Reconnect the gas line to the tank and tighten it with a pipe wrench. Use a gas leak detector or soapy water to check for any leaks before proceeding.
7. Fill the Tank with Water
Once everything is connected, it’s time to fill the tank with water.
- Open the Cold Water Valve: Slowly turn on the cold-water supply valve to allow water to fill the tank. Keep an eye on the connections to make sure there are no leaks.
- Open a Hot Water Tap: Open a hot water tap to help release any air trapped inside the tank, allowing the water heater to fill completely.
8. Check for Leaks and Test the Heater
Once the tank is full of water, check all connections for leaks, and then turn on the power or gas.
- Check the Water Lines: Examine both the hot and cold water lines for any signs of leaks.
- Turn On the Heater: Switch the power back on at the breaker (for electric heaters) or ignite the pilot light (for gas heaters).
- Allow Time for Heating: Wait about 30-60 minutes for the water to heat up. After that, check the water temperature from a hot water tap to ensure the unit is working properly.
9. Clean Up and Final Checks
Once the water heater is functioning, clean up your work area.
- Dispose of the Old Heater: Arrange for the old water heater to be recycled or disposed of according to local regulations.
- Final Inspection: Do a final inspection of the area to make sure everything is secure, there are no leaks, and the heater is operating correctly.
Conclusion
Replacing a water heater can be an involved process, but by following these step-by-step instructions, you can do it yourself and save money. Make sure to take your time, double-check all connections, and ensure everything is securely installed. If at any point you feel uncomfortable, don’t hesitate to call a professional to complete the installation. With the new water heater up and running, you can enjoy reliable hot water for years to come.