I get commissions for purchases made through links in this post.
Water heaters are essential in most households, providing hot water for showers, dishwashing, and other daily tasks. Like any appliance , they need regular maintenance to ensure they run efficiently and last longer. With proper care, you can extend the lifespan of your water heater , prevent costly repairs, and even reduce your energy bills. Here’s how to perform basic water heater maintenance that anyone can do.
1. Check the Temperature Setting
Most water heaters come with a thermostat that allows you to adjust the water temperature. Setting the temperature too high can cause energy waste and even scalding accidents, while setting it too low may not provide enough hot water for your needs. The ideal temperature setting is around 120°F (49°C). Here’s how you can adjust it:
- Locate the thermostat on the side of your water heater.
- Use a flathead screwdriver to adjust the temperature setting.
- Once you’ve set the temperature to the optimal level, allow the water to heat up and check the temperature by running hot water from a faucet.
2. Inspect the Anode Rod
The anode rod is a vital part of your water heater that helps prevent rust and corrosion. Over time, it will degrade and need replacement. If the anode rod is worn out, it could lead to tank corrosion, which may result in leaks or other issues.
To inspect and replace the anode rod:
- Turn off the power supply to the water heater.
- Close the water supply valve and drain a small amount of water from the tank.
- Locate the anode rod (usually found at the top of the tank).
- Use a wrench to remove the rod. If it’s covered with corrosion or significantly worn, it’s time to replace it.
Anode rods are inexpensive and easy to replace. It’s a good practice to inspect it every 1–2 years.
3. Flush the Tank
Sediment and mineral buildup in the tank can reduce the efficiency of your water heater and even cause it to overheat or fail. Flushing the tank helps remove these deposits and keeps your heater running smoothly.
To flush the tank:
- Turn off the power supply to the water heater (for electric models, turn off the breaker ; for gas models, set the thermostat to “off”).
- Turn off the cold water supply to the tank.
- Attach a garden hose to the drain valve at the bottom of the tank and place the other end of the hose in a drain or outside.
- Open the drain valve and let the water run until it flows clear.
- Close the valve , disconnect the hose , and turn on the cold water supply to refill the tank.
- Turn the power back on and allow the water heater to heat up.
Flushing the tank once a year is generally sufficient, but if you live in an area with hard water, you may need to do it more often.
4. Check for Leaks
Leaks around your water heater can be a sign of a malfunction or wear and tear. Water heaters are usually installed in places where leaks may go unnoticed, so it’s important to regularly inspect the area around the tank for any signs of moisture or pooling water.
Here’s how to check for leaks:
- Look for any damp spots or puddles around the base of the tank.
- Inspect the pipes and connections for any drips or signs of water escaping.
- If you find any leaks, shut off the water supply immediately and contact a professional plumber to address the issue.
5. Insulate the Tank and Pipes
Insulating your water heater and the hot water pipes can reduce energy loss, especially in colder climates. This is a cost-effective way to help your water heater work more efficiently.
To insulate the tank:
- You can buy a pre-made water heater insulation blanket from a hardware store.
- Wrap the blanket around the tank, securing it with the included straps. Ensure the thermostat area is exposed for easy access.
To insulate the pipes:
- Wrap foam pipe insulation around the hot water pipes, focusing on the first few feet of pipe leading from the tank. This will prevent heat loss and improve energy efficiency.
6. Test the Pressure Relief Valve
The pressure relief valve is a safety feature designed to prevent excess pressure from building up inside the water heater. It’s important to test it periodically to ensure it’s working properly.
To test the valve:
- Locate the valve, which is usually found near the top or side of the tank.
- Place a bucket or container underneath the valve.
- Lift the lever on the valve to let some water out. If water flows freely and then stops when you release the lever, the valve is functioning properly.
- If the valve is stuck or leaks continuously, it may need to be replaced.
Testing the valve annually is a good habit.
7. Look for Signs of Wear or Damage
Over time, your water heater will show signs of wear and tear. Regularly inspect the exterior of the tank for any signs of damage, such as dents, rust spots, or leaks. If you notice any of these signs, it may be time to consider replacing the unit , especially if the heater is older than 10 years.
8. Schedule Professional Maintenance
While regular DIY maintenance can help extend the life of your water heater, it’s also a good idea to have a professional plumber inspect and service the unit every 2-3 years. A professional can check the system for issues that may be hard to detect on your own and help prevent major problems down the road.
Conclusion
Regular maintenance of your water heater is essential to ensure it runs efficiently and lasts for years. By performing simple tasks like adjusting the temperature, flushing the tank, checking for leaks, and inspecting the anode rod , you can avoid costly repairs and extend the life of your water heater. Remember to always prioritize safety, and when in doubt, call a professional to handle more complex issues. With these basic maintenance steps, you’ll enjoy reliable hot water and save money on energy bills for years to come.