I get commissions for purchases made through links in this post.
A running toilet is one of the most common yet annoying plumbing problems homeowners face. Not only does it waste a significant amount of water, but it can also drive up your water bill if left unresolved. The good news is that most running toilet issues can be fixed with a little know-how and basic tools. In this post, we’ll walk you through how to diagnose the problem and resolve it quickly.
1. Understand the Common Causes of a Running Toilet
Before you can fix a running toilet, it’s important to understand why it’s happening. A toilet runs when water continuously flows from the tank into the bowl, often because of a malfunctioning component. Here are some common culprits:
- Flapper Valve: The flapper is a rubber valve at the bottom of the tank that controls the water flow into the toilet bowl. If the flapper doesn’t seal properly, water will leak into the bowl, causing the toilet to run.
- Float Issues: The float controls the water level in the tank. If it’s set too high, the tank will overflow and constantly refill.
- Fill Valve Problems: If the fill valve is malfunctioning, it might allow water to flow continuously into the tank, causing a running toilet.
- Overflow Tube: If the water level is set too high, it can flow into the overflow tube, which is designed to prevent water from spilling out of the tank, but it can also lead to a running toilet.
2. Turn Off the Water Supply
Before you start diagnosing or fixing the toilet, it’s essential to turn off the water supply to prevent flooding. The shutoff valve is typically located behind the toilet near the floor.
- Turn the Valve: Turn the valve clockwise to stop the water flow.
- Flush the Toilet: Flush the toilet to drain as much water from the tank as possible. This will give you better access to the internal components.
3. Inspect the Flapper Valve
The most common cause of a running toilet is a faulty or worn-out flapper valve. To inspect it:
- Remove the Tank Lid: Carefully lift off the tank lid and set it aside.
- Check the Flapper: The flapper should form a tight seal at the bottom of the tank. If it looks worn out, warped, or doesn’t close properly, it’s time for a replacement.
- Replace the Flapper: To replace the flapper, unhook it from the chain and lift it off the valve seat. Purchase a replacement that matches the model of your toilet and install it by hooking it in place and adjusting the chain so that there’s a slight amount of slack when the flapper is closed.
4. Adjust the Float
If the water level in the tank is too high, it can cause water to spill into the overflow tube and run continuously. Adjusting the float can solve this issue.
- Locate the Float: The float is either a ball or a cylindrical float attached to a rod connected to the fill valve.
- Adjust the Float: If it’s a ball float, bend the arm slightly downward to lower the water level. For a cylindrical float, use the adjustment screw to raise or lower the float position until the water stops about an inch below the overflow tube.
5. Examine the Fill Valve
If adjusting the float doesn’t resolve the issue, the fill valve could be malfunctioning. The fill valve controls the flow of water into the tank, and a faulty one can cause water to keep running.
- Check for Leaks: Look for signs of leaks or water flowing from the valve into the tank even after the toilet is full. This could indicate that the valve is stuck in the “open” position.
- Clean the Fill Valve: Sometimes, debris can clog the fill valve, preventing it from shutting off properly. Turn off the water supply, remove the valve cap, and use a small brush or toothbrush to clean any visible debris.
- Replace the Fill Valve: If cleaning doesn’t help, you may need to replace the fill valve entirely. To do this, disconnect the water supply line from the valve, remove the old valve, and install a new one by following the manufacturer’s instructions.
6. Check the Overflow Tube
The overflow tube is designed to prevent water from spilling out of the tank by directing excess water into the bowl. If the water level is too high, it can cause water to flow constantly into the tube.
- Inspect the Tube: Make sure the overflow tube isn’t cracked or damaged. If the water is constantly flowing into it, this indicates that the tank is too full.
- Adjust the Water Level: If the water level is above the overflow tube, you’ll need to adjust the float as described earlier to lower it.
7. Test the Toilet
Once you’ve inspected and replaced any faulty parts, it’s time to test the toilet.
- Turn the Water Back On: Slowly turn the shutoff valve counterclockwise to restore water flow.
- Flush the Toilet: Once the tank refills, flush the toilet to ensure everything is working properly.
- Check for Leaks: Monitor the toilet for any signs of leaking or running. If it still runs, double-check that all parts are installed correctly and adjust the float or valve settings as needed.
8. When to Call a Plumber
If you’ve gone through these steps and the toilet is still running, it may be time to call a professional plumber. Persistent issues could indicate a more complex problem with your toilet’s internal components or plumbing that requires expert attention.
Conclusion
Fixing a running toilet is often a simple and cost-effective DIY fix that can save you money on your water bill. By diagnosing the issue—whether it’s the flapper valve, float, fill valve, or overflow tube—you can quickly resolve the problem and restore your toilet to its normal function. Regular maintenance and occasional inspections will keep your toilet running efficiently for years to come.